Journal Paper

1. Majid Hashemzadeh, Negin Alsadat Sajjad, "Fiber laser cutting of aluminum sheets: an experimental investigation into energy ratio of EM/ESP", Journal of the Brazilian Society of Mechanical Sciences and Engineering, Vol 46, 2024, PP.461
    Status: Unavailable PDF
2. Majid Yousefi Tabar, Majid Hashemzadeh, Ali Razaei Rejani, "CO2 laser cutting of reinforced polyester (CGFRP and GFRP) sheets: An experimental investigation into specific point energy, cutting volume efficiency and material removal rate (MRR)", Journal of Manufacturing Processes, Vol 97, 2023, PP.137-147
    Status: Unavailable PDF
3. Ali Rezaei Rejani , Majid Hashemzadeh, "CO2 laser-air cutting of glass-fibre-reinforced unsaturated polyester (GFRUP): an experimental investigation", The International Journal of Advanced Manufacturing Technology, Vol 117, 2021, PP.2627–2638
    Status: Unavailable PDF
4. Majid Hashemzadeh, Mehdi Mohammadi, "The effect of power and maximum cutting speed on the material removal rate and cutting volume efficiency in CO2 laser cutting of Polycarbonate sheets", Journal of Modern Processes in Manufacturing and Production (MPMP Journal), Vol 9-1, 2020, PP.5-23
    Status: Available PDF
5. Majid Hashemzadeh, Reza Pourshaban, "The Effect of Power, Maximum Cutting Speed and Specific Point Energy on the Material Rremoval Rate and Cutting Volume Efficiency in CO2 Laser Cutting", Journal of Modern Processes in Manufacturing and Production, Vol 9-3, 2020, PP.23-39
    Status: Available PDF
6. Mohammad Davary, Majid Hashemzadeh, "The effect of bronze particles on CO2 laser cutting of reinforced polytetrafluoroethylene", International Journal of Advanced Manufacturing Technology, Vol 96-9, 2018, PP.4029–4039
    Status: Unavailable PDF
7. Hosein Taheri, Hamid Zarepour , Majid Hashemzadeh, "The Effect of Focal Distance and Type of Auxiliary Gas on Cut Width in CO2 Laser Cutting of Stainless and Mild Steel Sheets", International Journal of Advanced Design and Manufacturing Technology, Vol 11-4, 2018, PP.29-33
    Status: Available PDF
8. Majid Hashemzadeh, John Powell, Katy Voisey, "Fibre laser piercing of mild steel – The effects of power intensity gas type and pressure", Optics and Lasers in Engineering, Vol 55, 2014, PP.143-149
    Status: Unavailable PDF
9. Majid Hashemzadeh, Katy Voisey, Mehrdad Kazerooni, "The effects of low-frequency workpiece vibration on low-power CO2 laser cutting of PMMA: an experimental investigation", The International Journal of Advanced Manufacturing Technology, Vol 63, 2012, PP.33-40
    Status: Unavailable PDF

Conference Paper

1. Majid Hashemzadeh, Wojciech Suder, Stewart Williams, John Powell, A.F.H. Kaplan, Katy Voisey, "The application of specific point energy analysis to laser cutting with 1 m laser radiation ", 8th International Conference on Photonic Technologies LANE 2014, Germany, 2014
    Status: Available PDF
2. Majid Hashemzadeh, Mehrdad Kazerooni, "The effect of polymer melt and mold temperature on the distortion of polyoxymethylene plastic parts", 2nd Najafabad Manufacturing Engineering Conferance, Najafabad branch, Islamic AZAD University, 2009
    Status: Available PDF
3. Farid Malekahmadi, Mohammad Mahdavi, Majid Hashemzadeh, "Design and manufacturing of intelligent emergency stop equipment for turning and milling machines", Najafabad Manufacturing Engineering Conference, Najafabad branch, Islamic AZAD University, 2008
    Status: Available PDF
4. Mohammad Hosein Fatemi, Majid Hashemzadeh, "The influence of the spark parameter on the diagrams related to the monitoring of the fluctuations of the car exhaust gas", Najafabad Manufacturing Engineering Conference, Najafabad branch, Islamic AZAD University, 2008
    Status: Available PDF
5. Hosein Nejatbakhsh, Mohsen Fatehi, Majid Hashemzadeh, "Design of plastic injection molding (overmolding kind) to produce hollow parts using TCIM procedure", Najafabad Manufacturing Engineering Conference, Najafabad branch, Islamic AZAD University, 2008
    Status: Available PDF
6. Majid Hashemzadeh, Mehrdad Kazerooni, "New Methodology to Design of Gear Tolerance in Injection Molding Manufacturing", 2nd Tehran International Congress on Manufacturing Engineering, IRAN University of Science and Technology, 2007
    Status: Available PDF
7. Mehrdad Kazerooni, Afshin Kazerooni, Majid Hashemzadeh, "Design principles of CNC three-roller bending machine", 5th international , Guilan University-Faculty of Engineering, 2001
    Status: Available PDF